Today’s consumers expect glass to be a perfect, invisible product. Glass has imperfections, however, like all man-made products. And often, that is fine. Problems arise when an issue is noticed – and we are no longer able to look past it.

The most common quality issues that arise in tempered glass are roller waves, glass distortion, bad anisotropy and white haze. In this post, we want to focus on white haze and ways to control it.

White haze can be described as very small scratches, which appear on the glass surface as vague, foggy areas or repetitive stripes. The phenomenon is also called “ghosting.”

One of the most common signs of white haze is a long blemish in the center of the glass. The effect can also appear near the edges, on the corners – or even all over the glass.

There are many reasons why white haze can occur, and all of them can be solved by eliminating the root cause. A systematic approach is key here.

In our experience, up to 80% of white haze issues are caused during the processes prior to tempering. Only around 20% appear as a result of tempering itself.

Most white haze is nothing more than glass dust generated by the edge grinding process. The dust should be washed off the preprocessed glass in the washing machine. However, if the water wasn’t cleaned properly beforehand and starts recirculating, it creates a fine dust layer on the glass. During tempering, this layer fuses onto the glass and appears as white haze.

The solution is to wash and rinse the water tanks of the glass washer often and properly – if necessary, more than once per day.

Another measure that helps reduce the severity of possible white haze before tempering is to check which side of the glass has the tin side. When float glass is manufactured, one of its sides touches the molten tin, which then leaves an invisible tin coating on the glass. The other side is known as the air side. Checking which side is which is easy with a short-wave ultraviolet light, which reveals the slight fluorescence the tin coating side obtains.

Keep in mind that white haze appears more severely on the air side. So, run the glass tin side against the rollers whenever possible.

The most common reason for white haze in the tempering process itself is residue on the furnace rollers. This residue then causes tiny scratches on the glass surface.

If this is the case, examine the roller surfaces. Are they rough, cracked or brittle? Are there any solid particles on the surfaces? If so, take corrective action accordingly.

It’s important to ensure there is no chance of dust flying into the furnace. General cleanliness of the production environment is key. In addition, take care to inspect the insulation. Furnace doors should be in perfect operating condition to prevent any particles from entering the machine.

The leveling of the rollers is also important. If they are not properly adjusted, white haze can be caused by mechanical pressure that is too strong between the glass and the rollers.

Last but not least, check out the drive system. Is the drive speed consistent? Are the belts in good condition? Make sure the roller bearing works well.

If the root cause is in the process parameters, you will notice that the defect is not always repeated. It may be only a certain glass thickness or type that ends up with white haze marks.

If you’re dealing with non-optimized tempering parameters, you should be able to fix the issue by adjusting the settings to run the glass as flat as possible. One way of doing this is by decreasing the temperature of the bottom section and/or increasing the top convection. Note! Excessive top convection creates a different glass quality issue.

Even though white haze on tempered glass often looks like a quality issue, the safety and durability of such glass are not affected. If it breaks, the glass will still behave like normal safety glass.

No defects are ever welcome – especially those that are clearly visible. Issues like white haze have a direct impact on glass processors’ profit. No wonder we all strive to keep it to an absolute minimum.

But can you know if a particular type of white haze is acceptable by the industry? Actually, now you do!

Via Fieramonti 1 04012 Cisterna di Latina LT Italy

Pol. Ind. Penapurreira Parcela C4-B, 15320 As Pontes de García Rodríguez A Coruña Spain

No. 20 Binhe Road, High-tech Development Zone, Luolong Qu Luoyang Shi Henan Sheng , 471003 China

25F, Huarun Mansion A, 6 Shandong Road, Qingdao, PR China Qingdao Shi Shandong Sheng , 266071 China

Runów, ul. Solidarności 1 05-504 Złotokłos Poland

Via Marcatutto 7, (Milano) Italy 20080 Albairate MI Italy

No. 160 Yichuan Rd., Jiaonan Shi Qingdao Shi Shandong Sheng , 266000 China

3196 Thompson Road Fenton , MI 48430 United States

Peter Lisec Straße 1, 3353 Seitenstetten Austria

5 Atir Yeda st. Kfar Saba 4464305 Israel

100 Schelkovskoye Highway, building 108, room 45 Moscow Moskva 105523 Russia

Im Vogelsang 18 3340 Waidhofen/Ybbs Austria

V. alla Porada, 188 20831 Seregno MB Italy

Ctra. Estación Km. 15.8 44415 Rubielos de Mora Teruel Spain

Polígono Industrial El Bayo, parcela I, 19 24492 Cubillos del Sil León Spain

Industrijska zona R.Z. R29 51223 Kukuljanovo Croatia

12 place de l’Iris 92400 Courbevoie France

Via del Lavoro, 1 22036 Erba CO Italy

Changzhou Xingchen Industry Park Wujin Qu Changzhou Shi Jiangsu Sheng , 213119 China

Log in or register to post comments